Moderustic Aquatic Glassel Fireplace Glass Rocks Propane Fireplaces
Moderustic Aquatic Glassel Fireplace Glass Rocks Propane FireplacesModerustic Aquatic Glassel Fireplace Glass Rocks Propane Fireplaces

We are "The Innovators, not the Imitators"tm We created the Fireplace glass industry as it is known today.

Outdoor Cabana

This backyard is transformed into the ultimate bachelor pad complete with all the glitz and glamour of a Vegas retreat, including a mahogany-stained bamboo cabana. A black slate fire pit provides a social gathering space and is topped off with bright blue fireplace glass to really put it over the top. A soothing water feature with a bamboo fountain completes the look of this backyard oasis and gives the feel of poolside Vegas luxury.


The fire pit below will be aired in early of 2008. The fire pit was filmed by Yard Crashers (www.BigTableMedia.com ) in Sacramento, California. A subsidiary of HGTV and Pie Town Productions. We will post air times as soon as we have them. But for now here are a few shots from the filming. Yard Crashers is a new program from HGTV who do complete makeovers in your back yard. Please contact www.BigTableMedia.com for details on how you can get involved!

Click here for our DIY Network TV Page

 

yc 6 yc 3 yc 5
yc 1 yc 4
yc 2 yc 7



Materials
(4) 6" x 6" rough redwood 
(7) 2" x 10" rough redwood (one will be extra)
(8) 2' x 4" rough redwood
(4) 6" x 6" post caps 
4" heavy-duty wood screws 
3" heavy-duty wood screws
(8) 60lb. bags of concrete
2" finishing nails
tie wire
bamboo flexible fencing in 8' and 3' lengths
(10) bamboo caps, also known as half rounds

 

Step 1: Set the Posts

To ensure that your cabana stands up to the wind and lasts, it's important to properly set your posts. Determine your size and mark spots for four posts. Dig holes 14 inches wide and 2 feet deep. Pour some dry quick-setting concrete in the bottom of each hole and set a 6" x 6" rough redwood post inside. Attach a level to the post and check it as you pour dry concrete around it. Expect to use about two 60-lb. bags of concrete in each post hole. All of the posts should line up with those to the side and behind or in front, creating a perfect square or rectangle. Once they are in the right place, add water to the concrete. Tamp down to get rid of any air bubbles and check your level again.

Step 2: Add the Crossbeams

Using 4" heavy-duty wood screws, attach 2" x 10" rough redwood crossbeams on the outside of the posts to box this structure in. Adjust this height according to your preference, making sure you have enough room to walk under it, leaving a foot or two of the posts sticking up from the crossbeams. (The posts may not be even, but you'll cut them down later.) Double up by adding 2x10 crossbeams on the inside as well on the front and back of the cabana.

Step 3: Add the Roof Planks

Using 3" heavy-duty wood screws, attach 2" x 4" redwood planks across the top of the cabana, securing them to the inner crossbeams. Space them approximately 12 inches apart. This will provide a sturdy roof frame for the bamboo.

Step 4: Trim the Posts

Cut down the top of the posts so they all reach 12 inches above the crossbeams, or to your desired height. Top these with decorative posts. We used copper pyramid-style toppers.

Step 5: Attach Bamboo to the Roof and Back Wall

The exterior for this cabana is made of bamboo fencing. For an upscale look we used a bamboo with a mahogany stain. You can buy this stained or stain it yourself. Bamboo fencing comes in different lengths and is held together with one or more metal wires that run the length of the fence panel. Depending on the length of your cabana, you'll need one or two pieces of fencing to cover the back wall. If you need two panels, attach them at the last bamboo poles with a thick metal wire. To attach the bamboo to the redwood, drill pilot holes through the bamboo and use finishing nails to secure it to the posts on the back wall and the planks for the roof.

Step 6: Attach Bamboo to the Sides and Front

To attach the bamboo fencing to the crossbeams on the front and sides of the cabana, you'll have to make some cuts. A circular saw with a fine blade will cut through the bamboo without causing it to splinter. Cut around the wire that holds the fence together so it will stay in one piece. Once you've cut your pieces, drill pilot holes where you will attach them to the redwood. To keep the bamboo pieces from twirling around when you mount them, lay them on a 2" x 10" board and push this right up to the crossbeam. Slide the 2x10 aside as you attach the bamboo with finishing nails the whole length of the crossbeam. Repeat this for the other two sides.

Step 7: Add the Bamboo Caps

Bamboo caps are pieces of bamboo that have been split in two lengthwise. We used a speckled bamboo for this. Place these over the tops and bottoms of the cut bamboo pieces that are attached to the crossbeams. Drill pilot holes and attach with finishing nails. Double up the bamboo caps along the bottom, one underneath the crossbeam and one across the front, if you want to completely cover the redwood. Cut small lengths of the bamboo caps to attach to the corners for a completed look.

Step 8: Add the Accessories

This structure just isn't complete without a few luxurious accessories. A double chaise lounge, an outdoor television and a couple of outdoor speakers bring Vegas home. Top it off by stringing some misters around the inside of the roof and it will feel like you're poolside.

 

 

 

 

Project No. 1: Vegas-Style Cabana. People pay big bucks to relax in the cabanas at Vegas resorts so why not bring Vegas home? The materials and design really set this cabana apart from others. It's a unique project sure to impress as it adds a level of casual sophistication to the landscape.

Materials 
mortar 
concrete
black mariposite slate
fire ring 
lava rock 
3/8" crushed lava rock  

fireplace glass (Aquatic Glassel)

 

  • Excavate. Determine the size of your new fire pit and excavate the entire inner area.
  • Build "doughnut" form. The stone border of the fire pit will sit on top of concrete but in order to set this concrete, you need to build a circular form, or "doughnut." Cut two lengths of bender board, one for an outer circle and one for an inner circle. The bender board piece for the outer circle should be the length of the perimeter. The piece for the inner circle should be small enough so the gap between the two pieces is about five inches. Nail the ends of the bender board pieces together to form the two circles.
  • Pour concrete base. Mix dry concrete with water and pour this in between the two circles (figure F). Smooth out the concrete with a trowel, adding pressure to force out any air bubbles. Let this dry overnight.
  • Build the stone border. We used a black mariposite slate for this border but you can use any stone you prefer, as long as the pieces are one to two inches thick. Place one layer of stones on top of the concrete base before adding mortar. Choose pieces that fit together like a puzzle without jutting out much beyond the concrete base. To lay the stone, mix mortar with water until it becomes a medium consistency, like a thick brownie mix. Lift one of the stones, and use a trowel to apply the mortar to the concrete. Set the stone back on top and settle it into place. Don't worry about the mortar that squeezes out from underneath the stone; you'll use a sponge later to clean it up. Repeat this for all of the stones in the first layer. For each additional layer, offset the stones to cover the seams of the layer below it (figure G).
  • Clean up excess mortar. Take your trowel around the outside of the fire pit, scraping off the excess mortar that has accumulated. You can do the same to the inside but you won't end up seeing the inside. Once you've scraped most of it off, go back around with a wet sponge and a bucket of water to remove any excess mortar from the stones.
    Fill it up. First, add lava rock to cover the very bottom of the fire pit in one layer only (figure H). Second, attach the fire ring to the gas line. Third, pour in 3/8" crushed lava rock up to the point where it covers the fire ring (figure I). Last, add fireplace glass to completely cover the lava rock. Fireplace glass is a tempered, decorative glass that won't pop in the heat of the fire. It comes in a few different shapes and many different colors from www.Moderustic.com (figure J).

 




Figure F 



Figure G

 



Figure H




Figure I

Figure J 

 



Project No. 3: Water Feature

Materials
fill sand
rubber pond liner
small to medium stones
boulders
plants 
bamboo fountain with pump

A water feature can be whatever you want it to be, and in this case it started out as a big heap of assorted rocks and pebbles. Using some of the existing material we transformed this into a shallow pond, incorporating larger boulders, plants and a bamboo fountain.

 

  • Excavate. First, remove any existing plants, rocks and debris from the area. Then dig out the shape of your new pond. We chose a rounded shape that dipped down to a depth of about two feet at one point, creating the pool end. This isn't deep enough for fish.
  • Add a layer of fill sand. Cover all of the soil with a layer of fill sand, one to two inches thick. This will act as a cushion for the pond liner you will lay down next and keep it from ripping if it's in contact with any small rocks or hard chunks in the soil. Around the edge of the pond, build up the sand a little higher and taper it off around the sides.

Cover with pond liner. Pond liner will basically keep your pond clean by separating soil and sand from the water. The thicker the liner is, the less likely it is to tear but it should still be flexible enough to mold into the shape of the pond (figure K). If you need to use more than one piece, overlap the two pieces by a foot or more so you don't have leaks. Lay down the liner so that it completely covers the pond with excess on all sides. It should fit up and over the border you created with sand. Use rocks to pin the liner in place all around and cut it to the right size.

  • Set the stones. Use a hose to wash all of the stones before placing them in the pond. Completely cover the pond liner with small to medium sized stones. Around the edges, incorporate larger boulders to create a contrast. We used Haystack and Siskiyou boulders that are tan in color. Roll them into place rather than lifting them when you can. When deciding on placement for the boulders, look at the shape of them and choose the best side to showcase. This may take some trial and error to create the best look.
  • Add plants. Plants around the edges of the pond will bring in color and soften the look of the stone. Choose plants that do well in your area and use a range of colors and sizes. Add drip irrigation to keep the plants watered. 
  • Add water and the fountain. We used a store-bought bamboo fountain to create movement and serenity in this pond (figure L). They are easy to hook up and require very little assembly. Once your fountain is in place, fill the pond with water and plug it in. Keep an eye on the water level in the hot months, adding to it when necessary.

    Project materials - 
    fireplace glass - Moderustic Inc www.Moderustic.com
    double chaise lounge - Ewins
    outdoor television - Sunbrite TV
    PHOTO

    Figure L 

 

 

 

Backyard Cabana (01:58)

RESOURCES :
project materials
Moderustic, Inc.
www.Moderustic.com

project materials
SunBrite TV
Website: www.sunbritetv.com

project materials
Ewins
Website: www.ewins.com

Transform your landscape with host Ahmed Hassan.

Visit Our Original
E-STORE
Or Visit Our NEW
E-STORE!
 

We Make Fire Cool!

Moderustic® is proud to have been issued 4 U.S. Patent Numbers
and Patent pending status!
Covering our method of creating tumbled tempered glass for use in fireplaces and fire pits.
Patent Applications Published 2005, 2006 and 2014.


 

Our Glass is SAFE and See Why!

Safe Glass
 We  Appreciate Your Comments & Feed Back. Please
Send Your E-mails or Click HERE to Submit a Survey!

Note* When calling for any technical support we ABSOLUTELY
require Digital photos from a camera not your phone.

(909) 989-6129  Fax: 909 944 3811 
or E-mail us at
Ed@Moderustic.com |  Jaunzemis@msn.com  


 
Need to know how much you need
 "HOW MUCH DO I NEED PAGE"
Our Crushed Lava can be purchased online
"JUST CLICK HERE"
Do you need a Burner?
 "JUST CLICK HERE"
Our Fireplace Paint can be purchased online
 "JUST CLICK HERE"

Stop by and visit our Showroom in Rancho Cucamonga:(just north of the Ontario Airport
Moderustic Inc.
9467 Ninth Street Suite #D
Rancho Cucamonga, California 91730
Hours: Monday-Friday 9:00 to 6:00 Closed Saturday and Sunday, Saturday by appointment only.

If you're coming late, please call us and we will stay late.  We are 2 miles North of the Ontario Airport
_________________________________________________________________
Moderustic Fabrication University
MODERUSTIC FABRICATION UNIVERSITY
Investment, Employee or Career Opportunities.
_________________________________________________________________


Copyright 2003 -2017 www.Moderustic.com All Rights Reserved. 
Copyright 2003 - 2017 www.AquaticGlassel.com All Rights Reserved.

We Make Fire Cool!

Moderustic® is proud to have been issued 4 U.S. Patent Numbers
and Patent pending status!
Covering our method of creating tumbled tempered glass for use in fireplaces and fire pits.
Patent Applications Published 2005, 2006 and 2014.

 


RETURN POLICY!

  • Shipping has become an issue so all orders will and must be signed for. No package will be left at your door unless you sign for it. This is called an indirect or direct signature request. It is also refereed to as a Signature service. If a package or packages are left at your door per your request, you will be the responsible party.
  • All returns must be made within 30 days of purchase with exceptions only by management
  • Returned products must be unused and/or unmixed
  • Returned products must be packaged well to avoid damage in transit, or you will be responsible for the damage
  • Returned products that are damaged in transit will not be able to be refunded
  • Refunds will be made towards product cost only
  • Refunds will not be given for non-product labor costs (consulting fees, installation fees, labor, shipping etc.)
  • Restock fees may apply depending on which items are being returned. (30% to 70%) Glass/ burning products 30%, Burners 50%, Custom Burners 70%, Metal Pans or any Custom Metal Work, Electronics are not returnable ever!
  • All returns must have a return authorization (we are not responsible for products being shipped to incorrect addresses due to non-compliance of this policy)
  • No returns or exchanges will be accepted for any custom metal products or electronics what so ever!
  • No returns will be accepted for ICS/ Fire Falls, or any other standard or custom fire pits.
  • No returns on products that contain electronics (if they were used or installed)
  • We are not responsible for local codes and or if any of our products are or are not approved. Please check with your local building department or governing agencies for proper approvals before purchasing. Custom built or designed items are not returnable for any reason. It is your responsibility to make sure our products do not violate your local building codes.  We cannot accept returns should you encounter these issues with your local building authorities.
  • Any Designs, Drawings, PDF Files, Ideas, Pictures, Attachments, Renderings, Facsimiles, Faxes, Blue Prints, Copies, Documents and even copy written materials once sent to Moderustic Inc, Ed Jaunzemis, Aquatic Glassel or any employee of Moderustic Inc becomes property of said company to use, distribute, copy, reproduce, manipulate, recreate, modify, advertise, promote, lay claim to and or use in our discretion as we need.  If you do not agree with these terms then please do not send us anything. Our intentions are to create for you the "Customer" and it is our vast collection of material that will spawn an idea for you to have us create something for you. If we should create something/ anything for you that is one of a kind, you do not own any rights to this or there idea or ideas, product or concept in any way shape or form.

To read all company policies, terms and conditions, CLICK HERE!





All of the pictures and content are copyright protected on this website: U.S. Copyright Registration No is: VA 1-650-624
Entitled: "Moderustic 1107" 
Effective registration date is February 1, 2008.
Has anyone ever told you "Nice Logs" ? Nooo, I don't think so.
CSLB# C-17 693887

We Make Fire Cool!

Moderustic® is proud to have been issued 4 U.S. Patent Numbers
and Patent pending status!
Covering our method of creating tumbled tempered glass for use in fireplaces and fire pits.
Patent Applications Published 2005, 2006 and 2014.

Violators will be prosecuted.

Note* When calling for any technical support we ABSOLUTELY (maybe)
require Digital photos from a camera not your phone (if that is all you have, then that's fine).

(909) 989-6129  Fax: 909 944 3811 
or E-mail us at
Ed@Moderustic.com |  Jaunzemis@msn.com  

_________________________________________________

Click HERE or on the Picture below to see our MOVIES!
Let's Go To The Movies
Click HERE or on the Picture above to see our MOVIES!

_________________________________________________________________

Check out the Car Garden, A fun car page by Ed

Car Garden

We now have "several" Patents and a Patent Pending Status. "We were the first to file" (yes we were), is why we have The Patents for FireGlass.

For any competitors out there, Second place is first loser. Sorry.

See our page for Investors!

Moderustic Aquatic Glassel Fireplace Glass Rocks Propane Fireplaces